Data Acquisition and Signal Analysis from Measured Motor Currents for Defect Detection in Electromechanical Drive Systems

##plugins.themes.bootstrap3.article.main##

##plugins.themes.bootstrap3.article.sidebar##

Published Jul 8, 2014
Christian Lessmeier Olaf Enge-Rosenblatt Christian Bayer Detmar Zimmer

Abstract

This paper presents the development of a diagnostic method which uses the measurement of motor currents in order to detect defects in electromechanical systems. It focusses on two main topics: the acquisition of experimental data, and the development of the diagnostic method. The data acquisition was crucial for the successful development of a dedicated signal analysis method. For this purpose, a test rig for generating experimental training data was created. The rig provides the ability to simulate a wide range of defects experimentally. Different types of artificial defects, such as bearing damage or misalignments, were used; these are described in detail in the second section of the paper. The experimental data was obtained under varying operational conditions. Using all possible settings of operational parameters for data generation would mean excessive experimental time and effort. Therefore, a special approach using the theory of “Design of Experiments” was applied. By using a fractional factorial design based on orthogonal arrays, the number of experiments could be reduced significantly. Details of this approach are given in the third section. The main ideas of the classification algorithm, including some of the results, are summarized in the fourth section. A special method using a combination of Principal Component Analysis and Linear Discriminant Analysis was designed for the correct detection of damage or misalignments. With this method, a successful classification of the systems’ health state could be obtained.

How to Cite

Lessmeier, C., Enge-Rosenblatt, O., Bayer, C., & Zimmer, D. (2014). Data Acquisition and Signal Analysis from Measured Motor Currents for Defect Detection in Electromechanical Drive Systems. PHM Society European Conference, 2(1). https://doi.org/10.36001/phme.2014.v2i1.1488
Abstract 725 | PDF Downloads 238

##plugins.themes.bootstrap3.article.details##

Keywords

classification, features, Data Based Diagnostics, experimental test stand, bearing defect diagnosis, feature selection

References
Bayer, C., Bator, M., Enge-Rosenblatt, O., Mönks, U., Dicks, A., & Lohweg, V. (2013). Sensorless Drive Diagnosis Using Automated Feature Extraction, Significance Ranking and Reduction. 18th IEEE International Conference on Emerging Technologies and Factory Automation (ETFA 2013), September 10-13, 2013, Cagliari, Italy.
Box, G.E., Hunter, J.S., & Hunter, W.G. (2005). Statistics for Experimenters: Design, Innovation, and Discovery. Hoboken, NJ: Wiley & Sons.
Dean, A., & Voss, D. (2008). Design and Analysis of Experiments. Springer Texts in Statistics. Berlin, Germany: Springer.
DIN EN ISO 9000 (2005). European Committee for Standardization: Quality management systems – Fundamentals and vocabulary. Brussels, Belgium.
Duda, R.O., Hart, P.E., & Stork, D.H. (2000). Pattern Classification. Wiley Interscience.
Dunteman, G.H. (1989). Principal Component Analysis. Sage Publications.
Enge-Rosenblatt, O., Bayer, C., Schnüttgen, J. (2012). Modeling a drum motor for illustrating wearout phenomena. 9th International Modelica Conference – Modelica’2012, (pp. 889-896), September 3-5, 2012, Munic, Germany.
Jolliffe, I.T. (2002). Principal Component Analysis. Springer.
Lessmeier, C., Piantsop Mbo’o, C., Coenen I., Zimmer, D., & Hameyer. K. (2012): Untersuchung von Bauteilschäden elektrischer Antriebsstränge im Belastungsprüfstand mittels Statorstromanalyse, 9. Aachener Kolloquium für Instanthaltung, Diagnose und Anlagenüberwachung (pp. 509-521), November 14-15, Aachen, Germany. Aachener Schriften zur Rohstoff- und Entsorgungstechnik, Band 81, Stolberg, Germany: Verlag R. Zillekens.
Mardia, K.V., Kent, J.T., & Bibby, J.M. (1979). Multivariate Analysis. New York.
Paschke, F., Bayer, C., Bator, M., Mönks, U., Dicks, A., Enge-Rosenblatt, O., & Lohweg, V. (2013). Sensorlose Zustandsüberwachung an Synchronmotoren. 23. Workshop Computational Intelligence, (pp. 211-225), December 5-6, 2013, Dortmund, Germany.
Stack, J. R., Habetler, T. G. & Harley, R. G. (2004): Fault classification and fault signature production for rolling element bearings in electric machines. IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics and Drives (pp. 172–176), August 24-26, Atlanta, GA, USA. DOI 10.1109/DEMPED.2003.1234568.
Tran, V.T., AlThobiani, F., Ball, A. & Choi, B.-K. (2013): An application to transient current signal based induction motor fault diagnosis of Fourier–Bessel expansion and simplified fuzzy ARTMAP. Expert Systems with Applications 40 (13), pp. 5372–5384. DOI: 10.1016/j.eswa.2013.03.040.
Widodo, A., Yang, B.-S., Gu, D.-S., & Choi, B.-K. (2009): Intelligent fault diagnosis system of induction motor based on transient current signal. Mechatronics, 19, 680–689.
Wu, C., & Hamada, M. (2009). Experiments – Planning, Analysis and Optimization. Probability and Statistics. Hoboken, NJ: Wiley & Sons.
Zhen, D., Wang, T., Gu, F., & Ball, A. D. (2013): Fault diagnosis of motor drives using stator current signal analysis based on dynamic time warping. Mechanical Systems and Signal Processing 34 (1-2), pp. 191–202. DOI: 10.1016/j.ymssp.2012.07.018.
Section
Technical Papers

Similar Articles

<< < 1 2 3 4 5 6 7 8 9 10 > >> 

You may also start an advanced similarity search for this article.